CAN Open Router Module
inkl. mva.
A-CANOR/B CANopen® Router/B provides intelligent data routing between either EtherNet/IP™, Modbus® RTU or Modbus TCP/IP® and the CANopen bus network
The A-CANOR/B CANopen® Router/B provides intelligent data routing between either EtherNet/IP™, Modbus® RTU or Modbus TCP/IP® and the CANopen bus network. This allows the user to integrate CANopen devices into a Rockwell® Logix platform (e.g. ControlLogix® or CompactLogix™) or any Modbus device with minimal effort.
The module can be configured to be either a CANopen Master or Slave allowing the user to not only integrate CANopen devices into a Logix or Modbus system, but to also allow the user to use Logix, Modbus, or EtherNet/IP devices in an existing CANopen network (by using the CANopen Router B in Slave mode). In a Logix system the module can use Direct-To-Tag technology allowing CANopen devices to exchange data with a Logix controller without the need to write any ladder or application code in Studio 5000.
The module also provides a range of statistics to simplify the diagnostic process as well as a CANopen packet capture for remote diagnosis. A built-in webserver provides detailed diagnostics of system configuration and operation, including the display of CANopen operation and communication statistics, without the need for any additional software.
Features and Benefits
- CANopen Master or Slave.
- The router can be configured as an EtherNet/IP Target or Originator, Modbus Master or Slave, to read/write data from a CANopen network.
- EtherNet/IP, Modbus RTU (RS-232 and RS-485) or Modbus TCP/IP.
- Support for up to 124 CANopen Slaves (when in Master mode).
- CANopen Slave mode can emulate up to 128 PDOs with various CANopen node addresses.
- Support for up to 32 PDOs (receive and transmit) per CANopen Slave.
- Support for mapping of 128 SDOs with any type of operating interface.
- Time synchronization of the CANopen network.
- Direct-To-Tag technology for Logix controllers.
- Advanced diagnostics including packet capture and web server.
- Dual Ethernet ports which supports DLR (Device Level Ring).
- NTP (Network Time Protocol) for external time synchronization.
- Master Mode supports NMT message to initialize network.
- Supports CANopen LSS Node and Bit Rate assignment.
Specifications
EtherNet/IP Network
|
Specification |
Description |
|
Connector |
RJ45 |
|
Conductors |
CAT5 STP/UTP |
|
ARP Connections |
200 max. |
|
TCP Connections |
200 max. |
|
CIP Connections |
15 max. |
|
Communication Rate |
10/100 Mbps |
|
Duplex Mode |
Full / Half |
|
Auto-MDIX Support |
Yes |
|
Embedded Switch |
Yes, 2 x Ethernet ports |
|
Device Level Ring (DLR) |
Yes |
|
Network Time Protocol |
Yes |
Serial Port (RS-232)
|
Specification |
Description |
|
Connector |
9-way terminal (shared with RS-485) |
|
Connector |
24 to 18 AWG |
|
Electrical Isolation |
1000 VDC |
|
Supported Baud Rates |
1200, 2400, 4800, 9800, 19200, 38400, 57600, 115200 |
|
Parity |
Even, Odd, None |
|
Data Bits |
8 |
|
Stop Bits |
1 |
Serial Port (RS-485)
|
Specification |
Description |
|
Connector |
9-way terminal (shared with RS-485) |
|
Connector |
24 to 18 AWG |
|
Electrical Isolation |
1500 Vrms for 1 minute |
|
Supported Baud Rates |
1200, 2400, 4800, 9800, 19200, 38400, 57600, 115200 |
|
Parity |
Even, Odd, None |
|
Data Bits |
8 |
|
Stop Bits |
1 |
CANopen Network
|
Specification |
Description |
|
Connector |
5-way terminal, 5.08 mm pitch. |
|
Modes |
Master, Slave |
|
Supported Baud Rates |
10k, 20k, 50k, 125k, 250k, 500k, 800k,1M |
|
CANopen Terminator |
120 Ω (Software enabled) |
CANopen Master
|
Specification |
Description |
|
CANopen Slave Count |
124 |
|
PDO Count per Device |
32 |
|
SDO Mapping Count |
128 |
|
CANopen Slave Auto Parameterize |
Yes |
|
CiA 443 Support |
Yes |
|
NMT Messages |
Operational Control (e.g. Stopped, Preoperational, Operational), SYNC, TIME, EMCY |
|
Layer Setting Services (LSS) |
Node and BitRate assignment supported |
CANopen Slave
|
Specification |
Description |
|
PDO Emulation Count |
125 |
|
Emulated Devices Supported |
125 |
|
MPDO Supported |
Yes |
EtherNet/IP Target
|
Specification |
Description |
|
Class1 Cyclic Connection Count |
4 |
|
Logix Direct to Tag Supported |
Yes |
EtherNet/IP Originator
|
Specification |
Description |
|
Class1 Cyclic Connection Supported |
Yes |
|
Class 3 UCMM Connections Supported |
Yes |
|
Class 1 Connection Count |
5 |
|
Class 3 UCMM Connection Count |
5 |
|
Class 3 UCMM Mapping Count |
50 |
Modbus
|
Specification |
Description |
|
Modes Supported |
Modbus TCP/IP, Modbus RTU (RS-232, RS-485) |
|
RS-485 Termination |
125 Ω (Software enabled) |
|
Slave devices (Client/Master only) |
20 max. |
|
Modbus Mappings (Client/Master only) |
100 max |
|
Mapping Ranges |
0 to 65535 |
|
Base Offset |
Modbus (base 0); PLC (base 1) |
|
PDO Emulation Count |
125 |
|
Emulated Devices Supported |
125 |
|
MPDO Supported |
Yes |
Hardware
|
Specification |
Description |
|
Power Supply |
Input: 10 to 32 VDC, (70 mA @ 24VDC) |
|
Power Consumption |
1.8 W |
|
Dimensions (H x W x D) |
101.0 x 22.5 x 120.0 mm |
|
Connector |
5-way terminal, 5.08 mm pitch. |
|
Conductors |
24 to 18 AWG |
|
Enclosure Rating |
IP20, NEMA/UL Open Type |
|
Temperature |
-20 to 70 °C |
|
Earth Connection |
Yes, terminal based |
|
Emissions |
IEC 61000-6-4 |
|
ESD Immunity |
EN 61000-4-2 |
|
Radiated RF Immunity |
IEC 61000-4-3 |
|
EFT/B Immunity |
IEC 61000-4-4 |
|
Surge Immunity |
IEC 61000-4-5 |
|
Conducted RF Immunity |
IEC 61000-4-6 |
|
PDO Emulation Count |
125 |
|
Emulated Devices Supported |
125 |
|
MPDO Supported |
Yes |